P280 Glazing Bar

An aluminium structural glazing bar into which multiwall polycarbonate or glass can be fitted. When glazing with multiwall polycarbonate the P280 glazing bar is capable of spanning up to 3.2m between fixing points. For applications longer than 3.2m span, an intermediate cross purlin should be installed to create a further fixing point, alternatively use the P288 glazing bar which can span up to 4m.

The P280 can be supplied either as a pre-pack complete with the aluminium base bar and bar cap, both with gasket fitted and an end plate or as loose individual items. The P280 can also be supplied as a hipped glazing bar which uses the same cap however we change the standard gasket to a half round gasket which allows the sheet to be fitted at an angle.

Standard Glazing Bar

Reference:P280
Colour:Mill Finish, White or Brown
Length:3m, 4m and 6m
Span:3.2m

The P280 glazing bar consists of an aluminium base bar (ref.283) and a shaped aluminium glazing bar cap (ref.280), gaskets and an end plate (ref.280EP).

The base bar is fitted to the ridge and eaves support, the glazing sheet sits on the gasket and the cap is drilled at intervals no more than 400mm apart. Screws are then fitted through the cap into the central stalk of the base bar. The length of screw differs with each thickness of glazing sheet. A screw cover cap is needed to cover and protect the head of the screw.

For applications without good ventilation i.e. enclosed sides, it is recommended that a uPVC thermal underclad be supplied to clip onto the base bar to minimise the risk of condensation forming. This is then known as the P284 glazing bar.

The P280 glazing bar is supplied as a pre-pack in 3m and 4m lengths with gaskets installed and as loose items in 6m. Mill finish as well as polyester powder coated white (RAL9910 satin) and brown (RAL8040 satin) are available as standard. We can also supply the aluminium painted to a specific RAL colour although this may be subject to a minimum quantity requirement and surcharge.

Hip Glazing Bar

Reference:P280H
Colour:Mill Finish, White or Brown
Length:3m and 4m (and 6m as non-standard)

To make the bar suitable for a hipped application, the gasket in the glazing bar cap and base is replaced by a half-round gasket and re-named as P280H.

The P280H is supplied as a pre-pack in 3m and 4m lengths and as loose items in 6m. The 3m and 4m pre-pack consists of the aluminium glazing bar cap and base, hipped gasket and a screw fit end plate.

Colour Options

Mill finish as well as polyester powder coated white (RAL9910 satin) and brown (RAL8040 satin) are available as standard. We can also supply the aluminium painted to a specific RAL colour although this may be subject to a minimum quantity requirement and surcharge.

   
Mill FinishRAL 9910
White (satin)
RAL 8040
Brown (satin)
Please note: The colours shown are not 100% accurate and are for guidance only

Applications

  • Medium Span Roofing
  • Rooflights
  • Conservatories
  • Cross Purlin Roofing
  • Swimming Pool Covers
  • Car Ports
  • Canopies
  • Garden Centre Roofing
  • Porches

Glazing with Glass

The P280 glazing bar is suitable for use with glass. Twinfix cannot advise as to the spanning capability of the glazing bar or at what centres the glazing bars should be placed. We recommend that a mechanically fixed end plate similar to our SB-MEP end plate be fitted at the foot of each bar to stop the glass from slipping.

Complementary Fixing Accessories

Side TrimU Profile
Ref 272 - 10mm
Ref 273 - 16mm
Ref 275 - 25mm
Side TrimRef 252 - 10mm
Ref 253 - 16mm
Ref 255 - 25mm
U Profile
Eaves FillerFixing Buttons (white)Fixing Buttons (brown)
Ref 285F285 Eaves FillerRef 272 - 10mm
Ref 273 - 16mm
Ref 275 - 25mm
Ref 252 - 10mm
Ref 253 - 16mm
Ref 255 - 25mm
Anti-dust/Breather TapeButyl Flashing
Ref FT or PBT 10
Ref FT or PBT 16
Ref FT or PBT 25
Anti-dust/Breather Tape200/20 White
200/20 Lead
Butyl Flashing

Help & Advice

If you have a project in mind or would like help or advice on any of our products or services, please either ring us on 01925 811311, email us at enquiries@twinfix.co.uk or get in touch via the enquiry form on our Contact Us page.

 

Related Downloads

FilenameFile TypeSizeUploaded
P287 - All you need to know.pdf  P287 - All you need to know.pdfPDF168 KB17/02/2016
P284 - Fixing Instructions.pdf  P284 - Fixing Instructions.pdfPDF1.48 MB17/02/2016
P284 - All you need to know.pdf  P284 - All you need to know.pdfPDF187 KB17/02/2016
P280 - Glazing Bar Info Sheet.pdf  P280 - Glazing Bar Info Sheet.pdfPDF746 KB17/02/2016
P280 - Fixing Instructions.pdf  P280 - Fixing Instructions.pdfPDF1.48 MB17/02/2016

Related FAQs

1. Can I use your glazing bars to install glass?
You can use all of our bars to install glass, with the exception of the P600 and P700 Snap-fit systems. However, please note that you will need to use a Mechanical End Plate to ensure the glass is held securely in place; the plastic end plates that are supplied with the bars are only suitable for use with multiwall polycarbonate.